Page 361 - Brewers_Catalogue_2025

SAILS AND SHEETS!

BARTON BOOMSTRUT
Patented flexing spring provides fast response and a constant force for vang efficiency. Lightweight with a
low-profile design and features two flexible coated fibreglass rods which provide the force to support the boom.
Pulling the boom down with a conventional kicker causes the Boomstrut to flex upwards; releasing straightens the
rods, thereby lifting and supporting the boom.Maintenance-free durable design that eliminates friction and sliding
parts Improved performance through less weight and windage Easy Installation. No need to replace your existing
hardware – the Boomstrut mounts independently inside the existing kicking strap tackle. Simple to follow instructions.
The Mast Fitting can use existing luff groove. The Boomstrut’s boom bracket is contoured to fit both round and flat boom
profiles.The key benefits are:• No more topping lift hassles• No adjustments and no hang-ups• Never again will your boom
fall accidentally • Safer and can prevent injury
max stroke at
suggested max tip pin to pin max rods can max initial full
item # full force
boat length weight length be reduced by adjustment
adjustment
B44020 19 - 24.6ft 9.5lbs 42-1/8” 5-7/8” 11-13/16” 6” 308lbs
B44030 24.6 - 29.5ft 15lbs 46-7/16” 5-7/8” 11-13/16” 6” 407lbs
B44035 29.5 - 34.4ft 19lbs 51-15/16” 5-7/8” 15-3/4” 7-7/8” 506lbs
B44040 34.4 - 39.4ft 23lbs 57-1/16” 5-7/8” 15-3/4” 7-7/8” 594lbs
The 'Wincher'
A specially designed rubber moulding which fits over the top of standard winches,
converting them to self-tailing. This simple operation works when the line is sheeted under
load, which means the coils climb up the winch drum and then become gripped
by the underside of the Wincher's rubber body. Cleating is achieved by locking the
sheet into the Wincher's ribbed
central groove. Barton 'Winchers'
are easy to fit and available in four item # max drum max rope
sizes to suit a wide range of popular B21641 64-70mm 8-10mm
winches. Full fitting
B21642 70-80mm 10-14mm
instructions are included.
B21643 80-90mm 12-14mm
B21644 90-100mm 12-16mm
Lazy Jack Kits
Allow mainsails to be reefed or dropped with ease, by retaining the sail between lines running from the mast (near the
hounds) to the boom. These lines can be slackened whilst sailing to avoid restricting sail shape.
Ideal for use with fully battened or conventional mainsails, these complete kits contain stainless steel,
plastic-coated wires with blocks and fixing eyes attached. High quality braided line, all fixings and
comprehensive fitting instructions are also included. A unique feature of Barton lazy jack kits is the soft plastic block
covers which prevent sail chafe and enhance appearance.
Lightweight (all rope kits)
For Boats up to 30ft - B41140
Cascade system for Boats up to 35ft - B41143
Standard
For Boats up to 30ft -B41150
Reefing Kits
Single line reefing kit
A boxed complete single-line reefing kit that allows reefing lines to be led aft to the safety of the cockpit.
This system makes reefing your mainsail a quick and easy operation - just lower the main to a
predetermined mark on the halyard, tension and reefing line and re-trim the sail. Supplied as a complete
set with all the parts and fittings required, together with full fitting instructions. All you need to provide is
a line and a cleat stopper. For Boats up to 30ft B41130
Slab reefing kits
Supplied with sliding blocks which are held in place with spring-loaded plungers.
Manufactured from stainless steel and 'Spectro' anodised aluminium. Available in
two sizes and complete with sufficient length of 'T' track and end stops.
For Boats up to 28ft - B41483
For Boats up to 39ft - B41496

email:info@brewersmarine.com 339